Engineered roofing systems built for Miami squalls.

High Point Roofing Corp installs, remediates, and maintains residential and commercial roof assemblies under the Florida Building Code High Velocity Hurricane Zone provisions.

HVHZ Wind Speeds to 175 mph ASTM D1970 Self-Adhered Underlayment Miami-Dade Notice of Acceptance (NOA)

Strip.

Substrate soundness is non-negotiable: fresh shingles are never nailed over decayed CDX plywood decking.

Every enduring roof begins with structural substrate validation. Water infiltration from past storms degrades plywood sheathing and softens rafters long before stains appear on interior drywall. When we strip an existing roof down to the sheathing, we expose every softened board and re-fasten the entire diaphragm to current Miami-Dade uplift specifications.

Diagnostic · Labor Scope

Emergency Roof Leak Repair

Targeted water infiltration diagnostics for acute roof penetrations. We trace water entry paths along valley transitions, cracked ridge caps, damaged plumbing boots, and deteriorated exhaust vents.

Labor Scope: Direct Diagnostic & Mechanical Seal

Materials Covered: Lead boots, elastomeric mastic, flashing

Dispatch Protocol: Dispatched after physical inspection

$140 – $930 labor Request Inspection

Remediation · Structural Labor

Water-Damage Roof Leak Repair

Severe infiltration remediation where moisture has penetrated deep into interior ceilings, insulation, and framing. We open saturated sections, sister damaged truss rafters, and rebuild the dry-in barrier.

Labor Scope: Framing, Deck Tear-Out & Water remediation

Structural Wood: Pressure-treated SPF and CDX plywood

Typical Range: $930 – $5,600 labor per project

$930 – $5,600 labor Request Inspection

Substrate · Unit Rate

Roof Decking Replacement

Deck repairs run $185 to $465 per 100 square feet, measured and billed solely where rot exists. We remove rotten sheathing, re-nail framing to code with 8d ring-shank nails at 6-inch centers, and install fresh 5/8-inch APA-rated CDX exterior plywood.

Sheathing Material: 5/8-inch APA Rated CDX Plywood

Fastener Code: 8d Ring-Shank Nails @ 6" edges / 12" field

Billing Basis: Measured chalk area per 100 sq ft

Macro detail of new plywood roof decking sheathing fastened with code-approved ring-shank nails

$185 – $465 per 100 sq ft Request Inspection

Installation of self-adhered secondary water barrier membrane along a roof valley

Valley dry-in · Self-adhering secondary water barrier Miami-Dade HVHZ compliance · Zero staples permitted

Seal.

Flashings and membranes built to withstand ponding water and driving rain.

In South Florida, ninety percent of localized roof leaks occur where vertical masonry walls join horizontal slopes. Mortar joints crack over time under intense heat cycles. We fabricate custom-bent sheet metal flashings and heat-weld thermoplastic membranes to form seamless barriers against hurricane wind-driven rain.

Sheet Metal · Labor Scope

Roof Flashing & Counter-Flashing Repair

Custom-bent step flashing, parapet wall reglets, and chimney crickets. We cut clean mechanical reglet grooves into exterior stucco, insert 26-gauge galvanized or aluminum flashing, and seal with elastomeric polyurethane.

Metal Gauge: 26-gauge Galvanized or Aluminum

Wall Joint: Saw-cut mechanical stucco reglet

Sealant: ASTM C920 Class 25 Polyurethane

Custom fabricated metal roof flashing sealed into a masonry wall joint

$185 – $465 labor Request Inspection

Commercial · Flat Roofing

Flat Roof TPO / EPDM Membrane Systems

60-mil single-ply thermoplastic polyolefin (TPO) and vulcanized EPDM systems engineered for low-slope residential patios, multi-family roofs, and commercial buildings. Heat-welded seams form a continuous, puncture-resistant waterproof plane.

Membrane Thickness: 60-mil Reinforced Single-Ply

Seam Method: Robotic & Handheld Hot-Air Weld

Drainage Substrate: Tapered Polyiso Insulation Board

Hot air welding of thermoplastic TPO commercial single-ply roof membrane seam

$5.00 – $12.00 / sq ft Request Inspection

Secure.

Surface roofing systems engineered for extreme hurricane wind resistance.

Three primary pitched roof systems protect Miami-Dade properties under our installation protocols: 3-tab asphalt shingles for budget-conscious properties, multi-layer architectural dimensional shingles for standard residential homes, and concealed-fastener standing seam Galvalume for lifetime coastal performance.

Pitched · Economy Shingle

3-Tab Asphalt Shingle Installation

Clean, economical asphalt shingle replacement suited for rental properties and moderate-exposure residential slopes. Installed over self-adhering modified bitumen underlayment with hot-dipped galvanized fasteners.

Wind Rating: 60 mph baseline warranty

Underlayment: Peel-and-stick secondary barrier

Fasteners: Ring-shank galvanized nails

$3.50 – $6.00 / sq ft Request Inspection

Pitched · High-Wind Laminate

Architectural Shingle Installation

Heavy-duty multi-layer dimensional shingles rated to 130 mph wind uplift. Secured with the mandatory Miami-Dade 6-nail high-wind fastening pattern and enhanced shadow bands for superior aesthetic depth.

Wind Uplift: Rated up to 130 mph (ASTM D3161)

Nail Pattern: 6 ring-shank nails per shingle

Product Approval: Miami-Dade County NOA verified

Roofing technician nailing architectural dimensional shingles with pneumatic coil gun

$4.00 – $8.00 / sq ft Request Inspection

Architectural · Lifetime Metal

Standing Seam Metal Roofing

Standing seam 24-gauge Galvalume handles coastal salt air where exposed-fastener tin rusts out in five years. We install continuous mechanical double-lock panels secured with concealed expansion clips, eliminating surface screw holes entirely.

Metal Specification: 24-Gauge Galvalume Steel or .032 Aluminum

Fastener Style: Concealed sliding clips · Zero exposed screws

Wind Tolerance: Engineered for Miami-Dade Category 5 uplift

$8.00 – $16.00 / sq ft Request Inspection

Enforce.

HVHZ wind code standards are non-negotiable legal mandates, not suggestions.

Miami-Dade County enforces the most stringent building code in North America. High Point Roofing Corp pulls every required permit, coordinates city progress inspections, and provides engineering Notice of Acceptance documentation for every component used on your roof.

Code Requirement	Miami-Dade HVHZ Rule	Standard Outside HVHZ	High Point Roofing Corp Execution
Secondary Water Barrier	Mandatory self-adhering modified bitumen	Felt paper stapled to decking	ASTM D1970 peel-and-stick over 100% of roof area
Fastener Type	Corrosion-resistant ring-shank nails	Smooth shank or pneumatic staples	Hot-dipped galvanized ring-shank nails only
Shingle Fastening	6 nails per architectural shingle	4 nails per shingle	Strict 6-nail high-wind pattern below sealant strip
Decking Nailing	6" on center at edges, 12" field	12" on center universally	8d ring-shank nails spaced @ 6" along every rafter
Permitting & Inspection	Municipal dry-in & final inspection	Often skipped or homeowner-pulled	Contractor-pulled permits across all Miami municipalities

Schedule.

Book your on-site ladder inspection across Miami-Dade County.

Detailed on-site diagnostics verify decking condition, measure exact square footage, examine valley transitions, and deliver a transparent written proposal based on our confirmed unit rates. No storm-chaser markups and no pressure.

Request Inspection View Pricing Estimator

High Point Roofing Corp · 7105 SW 8th St, #202, Miami, Florida 33144 · Direct Dispatch: 305-801-5332